Porosity and shrinkage are two common defects in gray and ductile iron castings. Both leave voids in the metal, but their causes vary and require different corrections. You can see these defects on the casting surface or discover them during machining, inspection, or pressure testing. Their type and location help identify the cause and how to correct it.
Gas Porosity vs. Shrinkage Porosity
Gas porosity forms when gas is trapped in the metal or released by the mold or core as the casting fills and freezes. The voids are usually rounded and smooth-walled and tend to be scattered throughout the casting or concentrated near a core. Shrinkage porosity occurs when liquid metal cannot feed the contraction that happens as a section freezes. These voids are often irregular, jagged, and typically appear in the areas that solidify last.
Shrinkage is common in heavy sections, hot spots, and junctions between thick and thin walls. The shape and location of the voids help identify the cause, although gas and shrinkage porosity could occur in the same casting.
Common Casting Defects in Iron
| Defect | What it looks like | Common causes |
|---|---|---|
| Gas porosity | Rounded, smooth-walled voids, scattered or near a core | Moisture or gas from the mold or core, low permeability, gas dissolved in the melt, air entrained during pouring |
| Shrinkage porosity | Irregular, jagged voids in the last regions to solidify | Inadequate feeding, heavy sections, junctions of thick and thin walls, riser design or placement |
| Cold shut | A line or seam where two streams of metal did not fuse | Low pouring temperature, insufficient fluidity, turbulence |
| Misrun | A section that did not fill completely | Metal that cools before the cavity fills |
| Inclusion | Foreign particles of slag, oxide, or sand embedded in the metal | Slag or dross carried into the mold, sand that breaks away from the mold or core |
Defects That Form During Filling
Cold shuts, misruns, and inclusions form while the mold fills, before solidification begins. A university design-for-casting text lists low pouring temperature among the causes of misruns and cold shuts, and high pouring temperature for shrinkage voids. Inclusions such as slag, oxide, or sand can enter through furnace and ladle handling, fluxing practice, or gating design.
What Causes Gas Porosity
Common sources of gas porosity include moisture, gas released by mold and core binders, gas dissolved in the molten iron, and air entrained during pouring. Mold and core venting and permeability determine how easily gas escapes, while turbulence during pouring can entrain air.
Casting Design, Gating, & Feeding
Casting geometry affects how molten iron fills the mold and solidifies. Complex internal passages can trap gas, while thicker sections could require additional feeding as they solidify. Core design and placement also influence metal flow and gas venting.
Gating systems control how molten metal enters and fills the mold, and poor filling conditions introduce turbulence and entrained air. Feeding systems, including risers where required, supply additional liquid metal as the casting solidifies, and their design depends on the iron grade, the casting geometry, and how it solidifies. Together, gating and feeding design are the main tools a foundry has for controlling gas porosity and shrinkage. The ASM Handbook chapter on filling and feeding systems for cast irons covers the design principles in detail.
Gray and ductile iron behave differently as they solidify. Depending on composition, microstructure, and cooling conditions, graphite formation can offset some contraction.
Casting Inspection Methods Before Shipment
Inspection requirements are set during quoting, based on the drawing, applicable specifications, and intended service. Visual and dimensional inspection identify surface defects and nonconformities, but additional methods may be specified when internal soundness or pressure integrity matters. Radiographic testing can reveal certain internal issues, including porosity, shrinkage cavities, and inclusions, before a casting ships. Pressure testing may be required for pressure-retaining parts. The right methods and acceptance criteria depend on the component’s design, material, and service requirements.
Repairing & Accepting Porous Castings
Whether a porous casting can be repaired depends on the defect, its location, and applicable specifications. The buyer’s engineer might need to approve the repair before work begins. Acceptance criteria should also account for the casting’s intended service, particularly when defects occur in critical areas.
Casting Defects & Foundry Selection
In most casting programs, the buyer supplies the drawing and specification, and the foundry decides the gating, feeding, and molding. For OEM engineers and sourcing teams, the relevant question is how a foundry evaluates casting requirements before production and responds when defects occur. Complex castings with multiple cores present different molding, filling, and solidification challenges than simpler components.
Drawings and specifications should identify the material grade, dimensional requirements, and any inspection or acceptance criteria. Existing patterns and core boxes may also need evaluation, particularly when production transfers from another foundry.
No single scrap rate applies to every iron casting, because scrap depends on the alloy, part geometry, section changes, and process. A buyer can ask how a foundry tracks scrap by cause and what changes after a repeat part fails, since a quoted rate means little without the casting it applies to.
Gray & Ductile Iron Castings at Lake Foundry
Lake Foundry specializes in complex iron castings with demanding internal geometries, including pump casings, volutes, and other highly cored components. We produce low-volume gray and ductile iron castings for OEMs and industrial customers, from individual castings to recurring programs involving multiple part numbers.
Before quoting a job, we review the drawing, material specification, expected quantity, and any testing or inspection requirements. We also consider core design, placement, tooling, and machining requirements. This coordination is particularly important for castings where internal complexity presents greater manufacturing challenges than the external geometry. Here is what we offer:
- Finished casting size: Up to 12,500 lb in gray iron and up to 3,500 lb in ductile iron
- Pour capacity: Up to 15,000 lb of gray iron and up to 6,000 lb of ductile iron
- Pattern making: An in-house pattern shop producing foam and wood patterns, plus evaluating existing patterns and core boxes
- Molding: No-bake sand molding for large, complex iron castings, from one-off components to recurring low-volume production
- Quality: Production under an ISO 9001:2015 certified quality management system
Frequently Asked Questions
What is a hot tear in a casting?
A hot tear is a crack or fracture that forms from thermal stress during solidification. It differs from shrinkage, which is a cavity caused by insufficient feeding. Causes of hot tears include high pouring temperature, high cooling rate, low metal ductility, and mold or core design.
What is core shift in sand casting?
Core shift is a misalignment of the core in the mold cavity, which changes the casting’s shape or dimensions. Possible causes include improper core alignment, loose core prints, insufficient core support, and excessive pressure from the molten metal. It matters most on castings with internal passages, because the core position sets the wall thickness around them.
Does porosity affect the fatigue strength of ductile iron?
Porosity can reduce fatigue strength in ductile iron. ASM International notes that as ductile iron approaches shrinkage porosity, the graphite nodules tend to align, which can reduce fatigue strength. For parts that carry cyclic loads, set the porosity acceptance level in the specification with the design engineer.
Request a Quote
Lake Foundry reviews gray and ductile iron casting requirements for new and existing components. Submit any available drawing, material specification, 3D models, or part details for review.

